![]() ![]() The only people that can shed light on this is BMD support. So that is why (speculation on my part) the computer does not recognise it as a webcam. I suspect it might have something to do with them being able to record video at a high frame rates via the USB port on the PRO & ISO models, as such if you use a USB-3 cable I suspect that there are signals on pins that are not used in a webcam. It turn's out, if you want to use the Mini PRO or ISO as a webcam for Zoom or Teams etc. It really seemed odd to me, so as an experiment I swapped out the "USB-3"(blue plug) for the "USB-2"(white plug) and the ATEM Mini ISO immediately got recognised as a webcam. I then thought just make sure that the "USB-3" cable was faulty and maybe not properly seated, I swapped it back and the old ATEM Mini sprang to life!? I thought that maybe I did not connect it properly first time so I connected the ISO back again and the NUC once again did not recognise it as a webcam. I then connected the original ATEM Mini back again and it worked on the "USB-2" as well. I immediately thought that the cable was faulty, so I swapped the cable with a "USB-2" (the white plug) cable that happen to be terminated with a USB-C connector and to my surprise the ISO sprang to life. I found that very odd, I was using a "USB-3" (the blue plug) cable when I tried it unsuccessfully the first time. When I connected the original ATEM Mini into my NUC USB-3 port, it was recognised as a USB webcam, however when I connected the ATEM Mini ISO it did not. I have two ATEM Mini's, the original one and an ISO. Elgato and Blackmagic Ultra Studio does not have loopback connection ESPECIALLY MAGWELL fills that of External Monitor viewing and acting as Computer Web Cam for Zoom etc. Enter Youtube/Facebook Stream ID on the ATEM Mini Pro software control directly for live stream Connect Magwell USB connection to a Computer USB for Zoom ConferenceĦ. Connect Magwell HDMI Plus Loopback HDMI to a Monitor HDMI for output viewing including multi-viewĥ. Connect HDMI OUT to a Camera Capture Device like Magwell HDMI Plus (best choice), or Elgato Cam Link or Black Magic Ultra Studio Mini RecorderĤ. Connect External Hard Disk to USB-C for recordingģ. ![]() Connect ATEM MINI PRO to internet using EthernetĢ. View out put on a Monitor (multi-view or otherwise)ĭo the following to achieve all the above at the same time:ġ. Stream Live to Youtube or Facebook (one of them directly and many using third party distribution)Ĥ. If you would like to use ATEM MINI PRO to do the following simultaneously:ģ. Not sure where to go from here, so I'd really appreciate any ideas or suggestions. In Skype camera settings, it doesn't see it at all: "No device found." ![]() Please connect a camera and verify correct camera permissions in your browser." In OBS, the ATEM Mini is not recognized and doesn't show up as an option when setting up a new Video Capture Device.įacebook Live's camera dropdown shows "Blackmagic Design (1edb:be49)", but when I select it, it says "Unable to find camera. From there I can control the switcher without issue. I'm able to control the switcher perfectly from the ATEM Software Control program, though whenever I first open the program, I get "No device connected" displayed for a few seconds before the control panel interface appears. I've tried connecting the ATEM Mini to my computer using two different USB-C to USB-A cables - one USB 3.1 and one USB 2.0 - using different 2.0 and 3.0 ports on my computer. I have two cameras going into the ATEM Mini, both showing fine and switching/cutting properly on the HDMI-connected external monitor. I can't get OBS and various other programs to properly recognize the ATEM Mini USB "webcam".įor background: I've read the relevant sections of the manual as far as set-up, connecting to computer, etc, and I've installed the Blackmagic "ATEM Switchers 8.1 Update" software from. EDIT: Solution was to switch "Allow apps to access your camera" to ON in "Camera privacy settings" (Windows 10).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |